> Building Supplies > Concrete and Mortar

Lumberjack MB Flooring PrimerEverbuild Lumberjack MB Primer ... Read more

Lumberjack MB Flooring PrimerEverbuild Lumberjack MB Primer is is a one part, water and solvent free, moisture cure polyurethane liquid resin designed for treating concrete floors prior to laying wooden flooring. M.B Primer is particularly useful for blocking capillary dampness in screeds when the residual moisture content is above that recommended for laying wooden floors.Key Points Blocks moisture in damp screeds. Acts as a primer for dusty screeds. Helps bind the surface of weak screeds. 100% active, solvent and water free – will not cause warpage or curl of wood blocks/planks and is classified as low emission. Forms an excellent patching mortar when mixed 1:9 by weight with sand for repairing cracks and holes in concrete floors.Coverage 2 square metres per litre.ApplicationAs a waterproofing membrane: Screeds must be free from oil, wax, dirt and must be adequately cured (minimum 4 weeks old). Apply at least two coats of Lumberjack M.B Primer by roller or brush at 90 degrees to each other allowing at least 4 hours drying between coats. Allow final coat to dry for 24 hours before covering is laid. As an anti-dust primer or over existing adhesive residues. : Remove as much adhesive as possible mechanically. Apply with a roller or brush in a single coat. Allow to dry for 24 hours. The high penetration helps bind the surface. Minimize

10m. 3mm cross-linked polyolefin foam, adhesive backed unde ... Read more

10m. 3mm cross-linked polyolefin foam, adhesive backed underlay with integral vapour barrier and adhesive strip. Designed for use with engineered and solid wood flooring and suitable for installation on to concrete sub-floor, without separate vapour barrier. Features: 10 Year Protection; Spot Levelling (min. 2.7mm); Prevents Rocking & Sound Bridges; Joint Protection 0.5mm Deflection Under Load; Integral 125m PE Film Vapour Barrier & Adhesive Strip; Good Transmitted Sound Reduction. Specifications: Typical use: living room, kitchen and hallway. Performance/max. load: domestic/commercial, 250kg/m. Joint protection/compressive strength: 28kPa, 2800kg/m. Medium thermal insulation: 0.090m. Minimize

900 x 1500mm. Anti-Fatigue Mat designed to reduce discomfor ... Read more

900 x 1500mm. Anti-Fatigue Mat designed to reduce discomfort from standing on cold, hard, concrete floors for long periods. Bevel edged. 9.5mm thick. Use in dry environments only. Slip resistant to EN 13552 cat. R10. Fire tested to DIN 54332 (B2) part of DIN 4102. 9.5mm thick. Specifications: W x L x T: 900 x 1500 x 9.5mm. Minimize

Design service and technical advice available. Visit www.ph ... Read more

Design service and technical advice available. Visit www.philex.com/heating or call 0845 757 3479. Features: Professional Installation Required; Includes Thermostat; Comfort & Primary Heat; Suitable for Use with Concrete Floors; Ideal for Covering with Tile & Stone Flooring; IP66; Energy Efficient; 10 Year Manufacturer's Guarantee; Construction Material: Plastic / Metal; Suitable for Retro-Fit. Specifications: 230V. Cable type: twin conductor heating cable. Max. floor temp: 120C. 150W/m. RCD required. Connection via 16A thermostat. Insulation board recommended. Associated products: Thermal Board Kit (Quote 93806). Minimize

Ready-to-use white construction adhesive based on acrylic d ... Read more

Ready-to-use white construction adhesive based on acrylic dispersions, adheres to most common building surfaces and replaces nails and screws. Will adhere to masonry, concrete, plaster, chipboard and wood. Fixes PVC, skirting boards, thresholds, panels and ceramic tiles. One surface must be porous. Minimize

900 x 600mm. Anti-Fatigue Mat designed to reduce discomfort ... Read more

900 x 600mm. Anti-Fatigue Mat designed to reduce discomfort from standing on cold, hard, concrete floors for long periods. Bevel edged. 9.5mm thick. Use in dry environments only. Slip resistant to EN 13552 cat. R10. Fire tested to DIN 54332 (B2) part of DIN 4102. 9.5mm thick. Specifications: W x L x T: 900 x 600 x 9.5mm. Minimize

Design service and technical advice available. Visit www.ph ... Read more

Design service and technical advice available. Visit www.philex.com/heating or call 0845 757 3479. Features: Professional Installation Required; Includes Thermostat; Comfort & Primary Heat; Suitable for Use with Concrete Floors; Ideal for Covering with Tile & Stone Flooring; IP66; Energy Efficient; 10 Year Manufacturer's Guarantee; Construction Material: Plastic / Metal; Suitable for Retro-Fit. Specifications: 230V. Cable type: twin conductor heating cable. Max. floor temp: 120C. 150W/m. RCD required. Connection via 16A thermostat. W x D x L: 500mm x 3.2mm x 8m. Insulation board recommended. Associated products: Thermal Boards (Quote 93806 and 75113). Minimize

Design service and technical advice available. Visit www.ph ... Read more

Design service and technical advice available. Visit www.philex.com/heating or call 0845 757 3479. Features: Professional Installation Required; Includes Thermostat; Comfort & Primary Heat; Suitable for Use with Concrete Floors; Ideal for Covering with Tile & Stone Flooring; IP66; Energy Efficient; 10 Year Manufacturer's Guarantee; Construction Material: Plastic / Metal; Suitable for Retro-Fit. Specifications: 230V. Cable type: twin conductor heating cable. Max. floor temp: 120C. 150W/m. RCD required. Connection via 16A thermostat. W x D x L: 500mm x 3.2mm x 4m. Insulation board recommended. Associated products: Thermal Boards (Quote 93806 and 75113). Minimize

Mosaic Fix Adhesive 10kg is a brilliant white rapid setting ... Read more

Mosaic Fix Adhesive 10kg is a brilliant white rapid setting polymer modified cement based adhesive for fixing of tiles to a variety of substrates.The product sets in 40 minutes and can accept light foot traffic in 2 hours at 20oC. Minimize

5kg. Suitable for wood or concrete floors and ceramic, terr ... Read more

5kg. Suitable for wood or concrete floors and ceramic, terracotta, limestone and quarry tiles. Accelerant sachet included. Covers up to 1m. Sets in 4 hours. Specifications: Ready mixed adhesive. Powdered accelerant sachet included. Coverage 1m per 5kg. Minimize

Design service and technical advice available. Visit www.ph ... Read more

Design service and technical advice available. Visit www.philex.com/heating or call 0845 757 3479. Features: Professional Installation Required; Includes Thermostat; Comfort & Primary Heat; Suitable for Use with Concrete Floors; Ideal for Covering with Tile & Stone Flooring; IP66; Energy Efficient; 10 Year Manufacturer's Guarantee; Construction Material: Plastic / Metal; Suitable for Retro-Fit. Specifications: 230V. Cable type: twin conductor heating cable. Max. floor temp: 120C. 150W/m. RCD required. Connection via 16A thermostat. W x D x L: 500mm x 3.2mm x 16m. Insulation board recommended. Associated products: Thermal Boards (Quote 93806 and 75113). Minimize

Silicone Sealent - For Polycarbonate - 310ml Premier 450 Si ... Read more

Silicone Sealent - For Polycarbonate - 310ml Premier 450 Silicon Sealant is specially recommended for polycarbonate sheets, this product dries quickly to a flexible rubber seal, and will bond to most building substraights.Sticks best to: Timber Brick Stone PVCu Concrete Metal Minimize

Design service and technical advice available. Visit www.ph ... Read more

Design service and technical advice available. Visit www.philex.com/heating or call 0845 757 3479. Features: Professional Installation Required; Includes Thermostat; Comfort & Primary Heat; Suitable for Use with Concrete Floors; Ideal for Covering with Tile & Stone Flooring; IP66; Energy Efficient; 10 Year Manufacturer's Guarantee; Construction Material: Plastic / Metal; Suitable for Retro-Fit. Specifications: 230V. Cable type: twin conductor heating cable. Max. floor temp: 120C. 150W/m. RCD required. Connection via 16A thermostat. W x D x L: 500mm x 3.2mm x 12m. Insulation board recommended. Associated products: Thermal Boards (Quote 93806 and 75113). Minimize

5Ltr. Highly flexible, waterproof and ready-to-use. Tile di ... Read more

5Ltr. Highly flexible, waterproof and ready-to-use. Tile directly onto concrete floors. Dries charcoal grey. Specifications: Fixes and grouts up to 1.8m. Not suitable for use with underfloor heating. Minimize

Fast Set Flexible Adhesive is a fast set cement based adhes ... Read more

Fast Set Flexible Adhesive is a fast set cement based adhesive for fixing of tiles to a variety of substrates. The product sets in 40 minutes and can accept light foot traffic in 3 hours at 20oC. Minimize

5kg. Fast setting, mould resistant and water repellent. For ... Read more

5kg. Fast setting, mould resistant and water repellent. For interior or exterior use on dry or wet areas, timber floors and underfloor heating. Colour coordinates with Mapei Coloured Solvent-Free Silicone Sealant range. Colourfast. For joint widths 2-20mm. Specifications: CG 2 Minimize

1.8m. Ready-mixed, waterproof, floor tile adhesive and grou ... Read more

1.8m. Ready-mixed, waterproof, floor tile adhesive and grout. Specially designed, high-strength formula to withstand the pressure placed on solid concrete and cement screed surfaces. Dries beige. Minimize

With high tack adhesion. Ideal for fixing carpets to wood a ... Read more

With high tack adhesion. Ideal for fixing carpets to wood and concrete floors. Specifications: 50mm x 50m. Minimize

15kg. Grey setting, polymer enhanced, cement-based adhesive ... Read more

15kg. Grey setting, polymer enhanced, cement-based adhesive for floors and walls. Suitable for ceramic and porcelain tiles. Graduated. Mix with water. Includes free mixing bucket. Not suitable for use with underfloor heating or plywood overlays. Specifications: Not suitable for underfloor heating. Minimize

Ready-to-use white construction adhesive based on acrylic d ... Read more

Ready-to-use white construction adhesive based on acrylic dispersions, adheres to most common building surfaces and replaces nails and screws. Will adhere to masonry, concrete, plaster, chipboard and wood. Fixes PVC, skirting boards, thresholds, panels and ceramic tiles. One surface must be porous. Minimize

International Professional Floor Paint Tile Red 5 Litre ITL ... Read more

International Professional Floor Paint Tile Red 5 Litre ITLPFPRED5 For areas that have a professional purpose - such as in factories and warehouses - the floor paint used should be designed to accommodate the work undertaken on it.International Professional Floor Paint provides a tough and hardwearingfinish, which is resistant to chipping, flaking, scuffing and scratching.The paint provides excellent coverage â?" the paint will flow to fill cracks and crevices within the surface. With its water, oil and grease resistant properties, it is easy to clean and so is ideal for light industrial areas in warehouses, workshops, factories, showrooms, storerooms and utility rooms. Use it on interior and exterior concrete, stone, brick, wood, floor boards, MDF and chipboard.ITLPFPRED5 Professional Floor Paint has the following specifications:Colour: Red; Size: 5 litres. ITLPFPRED5 Minimize

Everbuild S.B.R Bond 5 Litre 503 EVBSBR5L EVERBUILD SBR BON ... Read more

Everbuild S.B.R Bond 5 Litre 503 EVBSBR5L EVERBUILD SBR BOND is a white liquid, which has numerous uses as an admixture, primer, bonding agent and sealer.Polymer Emulsions of this type have been used extensively over the last 20 years by the building industry as an admixture for cement and concrete applications, including repair and renovation, surfacing of floors and bonding generally. It contains anti-foam to control the density of cementitous mixes.- Greatly improved adhesion to a wide range of substrates including dense concrete,steel, tiles etc.- Mixes may be applied in much thinner sections- Excellent resistance to water and water vapour- A high level of resistance to salt permeation- Much improved toughness and flexibility- Reduced surface dusting of concrete- Greatly improved resistance to many chemicals- ideal for use in dairy parlours etc.- Reduced water: cement ratio for equivalent workability- Improved frost resistance-SBR Bond is also freeze thaw stable. EVBSBR5L Minimize

Bedec Superflex is a waterbased flexible elastomeric coatin ... Read more

Bedec Superflex is a waterbased flexible elastomeric coating,quickly applied by brush,roller or spray which dries to form a high build,seamless waterproof membrane.  Economically prevents or cures all types  of leaking roofs,gutters and walls.  Easy to apply,Super-flex remains flexibleand elastic to allow for movement of the substrate forming a long-life protective coating forweatherproofing roofs and walls.Uses: Suitable for application to almost any surface including roofing tiles,slate,brick,concrete,corrugated iron,asbestos,asphalt,felt,copper,zinc,most plastics and timber after suitable preparation.Available in 7 Colours including Solar Reflective White & Silver / Light Grey / Dark Grey / Tile Red / Green / BlackTypical ApplicationsApplication MethodsFelt RoofsBrush / RollerSlate/Clay Roof TilesCoventional SprayConcreteAirless SprayAsbestosTechnical DataDrying Times @ 20 Deg CTheorectical Spread Rate 2 sq mtrs / LtrTouch Dry 4 HoursVoc 140 Grms / LtrDry To Handle 4-6 Hours Minimize

Faithfull Concrete Frame Screws + Caps 7.5 x 182mm Box of 1 ... Read more

Faithfull Concrete Frame Screws + Caps 7.5 x 182mm Box of 100 FAIFXCFS182 A quick and simple self tapping fixing for most types of masonry, providing a virtually stress free fixing. Ideal for close to the edge applications. Through-Fixing eliminating the need for marking and re-positioning. These fixings have a high load capacity with interlocking thread into the base material. Torx head design for increased Torque control and easy driving. Bulk packs of 100 are supplied with T30 1/4 hex insert bit and cover caps. FAIFXCFS182 Minimize

Everbuild Tile on Timber 715 10Kg EVBTOT10 EVERBUILD Tile o ... Read more

Everbuild Tile on Timber 715 10Kg EVBTOT10 EVERBUILD Tile on Timber is a grey ready mixed paste tile adhesive with high flexibility and water resistance specifically designed for tiling directly onto timber floors. Tile on Timber is suitable for fixing all types of ceramic tiles, including vitrified, porcelain and mosaics and is ideal for application directly onto timber panels, plywood, composite board, tongue and groove floorboards and floating plywood floors. Tile on Timber is also suitable for tiling on cement based substrates and its grey colour enables Tile on Timber to be used as a floor grout. Conforms to BS5980 as a Type 2, Class AA adhesive and EN12004 Type D2. EVBTOT10 Minimize

Colour: Tile Red Size: 2.5 litre Coverage: 30m2, Touch Dry ... Read more

Colour: Tile Red Size: 2.5 litre Coverage: 30m2, Touch Dry in 1 hour, Walk on in 12 hours Quick Drying Suitable for interior and exterior concrete, stone & brick. Minimize

Rustins Quick Dry Floor Varnish Satin 5 Litre RUSAFCS5L Non ... Read more

Rustins Quick Dry Floor Varnish Satin 5 Litre RUSAFCS5L Non-toxic, quick drying, low odour floor varnish. Completely clear and non-yellowing.Resistant to water, alcohol, white spirit and similar solvents.Very hard wearing.Touch-dry in 20 minutes and re-coatable in 2 hours.Can be applied to wood, cork, MDF, concrete and unsealed terracotta and quarry tiles.Clean brushes in water. RUSAFCS5L Minimize

Faithfull Concrete Frame Screws + Caps 7.5 x 202mm Box of 1 ... Read more

Faithfull Concrete Frame Screws + Caps 7.5 x 202mm Box of 100 FAIFXCFS202 A quick and simple self tapping fixing for most types of masonry, providing a virtually stress free fixing. Ideal for close to the edge applications. Through-Fixing eliminating the need for marking and re-positioning. These fixings have a high load capacity with interlocking thread into the base material. Torx head design for increased Torque control and easy driving. Bulk packs of 100 are supplied with T30 1/4 hex insert bit and cover caps. FAIFXCFS202 Minimize

Rustins Quick Dry Floor Varnish Satin 2.5 Litre RUSAFCS25L ... Read more

Rustins Quick Dry Floor Varnish Satin 2.5 Litre RUSAFCS25L Non-toxic, quick drying, low odour floor varnish. Completely clear and non-yellowing.Resistant to water, alcohol, white spirit and similar solvents.Very hard wearing.Touch-dry in 20 minutes and re-coatable in 2 hours.Can be applied to wood, cork, MDF, concrete and unsealed terracotta and quarry tiles.Clean brushes in water. RUSAFCS25L Minimize